Used with pigments for countertops and floors

PE-100 LVX has a lower viscosity so that the material has better movement for metallic pigments .

PUR-VRM is a 100% solid, two part epoxy coating, designed to control the moisture vapor emission rate on deteriorated or new concrete floors.

Crystal clear casting epoxy used for mass castings with thicknesses greater than 1 in. and up to 4 in. ICECAST is an epoxy resin glue cured under normal temperature and low temperature conditions. It is UV resistant with anti-yellowing, strong adhesion, good fluidity, natural defoaming, small heat generation after mixing.

Crystal clear casting epoxy used for top coating or light casting with thicknesses smaller than 1 inch.  ICETHIN has a low VOC content, for user safety and reduced environmental impact. The low color and low viscosity allow for crystal clear castings ideal for art and hobby applications.

PP-HFAST is color stable allowing it to take UV exposure without color shifts seen with other coating systems such as epoxies. PP-HFAST is a 1:1 mix ratio system with sufficient pot life to be rolled, brushed, or sprayed .

PP-S85 is color stable allowing it to take UV exposure without color shifts seen with other coating systems such as epoxies. PP-S85 is a 1:1 mix ratio system with sufficient pot life to be rolled, brushed, or sprayed .

Write in the comments whether you want gloss or matte.

Write in the comments whether you want gloss or matte.

PP-CF is a two parts, high penetration, fast setting, hybrid polyurea for repairing and re-building damaged concrete. The product is a 1:1 ratio, easy to mix system that is 98 % solids and VOC compliant.

These Color Flakes, also known as a decorative vinyl color chips, come in 1/4″ sized for a consistent broadcast. These flakes are unique, random shaped, sized within a standardized range and custom blended to match any décor.

Glow-in-the-dark

This mixing bucket is used to mix and measure epoxy and pigments. Holds 1 quart. Printed with easy to read measurements.

This mixing bucket is used to mix and measure epoxy and pigments. Holds 5 quarts. Printed with easy to read measurements.

This 2 inch chip brush is used for “cutting in” epoxy into hard to reach areas.  Disposable

This roller frame goes with our 18" rollers

The 7” Edge Grinder with Frame is an affordable edge solution for smaller surface prep jobs. It is designed to operate while standing, avoiding wear on your knees and back. – 7” Bosch grinder on frame – 7” dust shroud – 110V – LED light – Weighs 46 lbs

10” rotary brush with risers, or 9” pads with pad driver. Ample power in a small and manageable machine.  Excellent balance with low center of gravity. It’s ideal for use in tight spaces, restrooms, edging and stairs. 1.0 HP, Dual capacitor, AC motor, 115-230V , 50/60 Hz power, Triple-planetary severe-duty 11:1 helical-cut industrial gears. Gears drive brushes and pads at 165 RPM, Thumb-operated safety switch. Dual steel operating triggers 1” x 5” non-marking ball bearing wheels.

The OMEGA 10” Grinder is ideal for working in tight, small spaces. Utilizes 3 pieces of standard WOLF Trap tooling. Equipped with an port for dust free grinding. Folds down for easy transport. – Width 10” – Single Head – 110V – 6500 RPM – Weighs 65 lbs – Single Phase -Motor 2.5 HP – Removable shroud for edge grinding

The 17″ Nomad is the perfect grinder or scrubber for anyone in the industry. With a 17″ path, it can be used efficiently in confined spaces as well as tackling large jobs just as easy. Although light weight and easy to transport, this grinder is incredibly strong and durable. -Motor 1.5 HP, 180 frame TEFC dual capacitor AC – Width 17” – 2 Head – 115-230V – Weighs 133 lbs – Optional 50 lb. weight set with transport lock.

The WARRIOR 20″ Grinder is the best quality and lowest cost floor grinder on the market. The WARRIOR is built for edging, grinding, and polishing concrete floors. It has variable speeds, an adjustable handle and adjustable head pressure. – Width 20” – 2 Head – 220V/240V – Single Phase – Motor 7.5 HP(5.5kw) – 1 additional 44 lb weight – Inverter 7.5 HP(5.5kw) – 8 Gal water tank – 50/60 HZ – 15 AMPS -300-1500 RPM – Weighs 330lbs

The DELTA 25” Grinder is ideal for both opened AND confined spaces. Built for low maintenance, the DELTA’s sleek, ergonomic design is perfectly balanced. Equipped with a durable, floating stainless dust shroud, and 3 flexible grinding heads. The locking adjustment handle means no pins to lose. The DELTA is operator friendly due to the easy to use control panel, built in tool box with tool kit, and 2 USB charging ports. Connects to Vac 3 for dustless operation. Working Width: 25″ Heads: 3 Volts: 220 Horsepower: 10 Water tank: 7 Gallons Inverter: 300-1800 RPM Phase: 1 or 3 Weight: 681 lbs. Grinding Pressure: 456 lbs. Amp Max: 45

The BETA 27” Grinder is ideal for both opened AND confined spaces. Built for low maintenance, the BETA’s sleek, ergonomic design is perfectly balanced. Equipped with a durable, floating stainless dust shroud, and 3 flexible grinding heads. The locking adjustment handle means no pins to lose. The BETA is operator friendly due to the touch screen control panel, built in tool box with tool kit, and 2 USB charging ports. Connects to Vac 3 for dustless operation. Working Width: 27″ Heads: 3 Volts: 220 Horse Power: 10 Water Tank: 7 Gallons Inverter: 300-1800 RPM Phase: 1 or 3 Weight: 720 lbs. Grinding Pressure: 523 lbs. Amp Max: 45

The ALPHA 30” Grinder is ideal for both opened AND confined spaces. Built for low maintenance, the ALPHA’s sleek, ergonomic design s perfectly balanced. Equipped with a durable, floating stainless dust shroud, and 3 flexible grinding heads. The locking adjustment handle means no pins to lose. The ALPHA is operator friendly due to the easy to use control panel, built in tool box with tool kit, and 2 USB charging ports. Connects to Vac 3 for dustless operation. Working Width: 30″ Heads: 3 Volts: 220 Horse Power: 10 Water Tank: 7 Gallons Inverter: 300-1800 RPM Phase: 1 or 3 Weight: TBD Grinding Pressure: TBD Amp Max: 45

The WOLF VAC 3 is equipped with a manual lever that will clean the filter with a jet pulse. It includes floor cleaning tools and comes standard with a HEPA filter. There are no circuit boards, which provide simple operation settings and a collapsible frame for easy transport. – 110V – 3 Motors – Weighs 176 lbs -Jet Pulse Filter cleaning – Includes wand, brush head and HEPA filter – 330 CFM – 26 Foot Hose

The WOLF VAC 3S is equipped with a manual lever that will clean the filter with a jet pulse. It includes floor cleaning tools and comes standard with a HEPA filter. There are no circuit boards, which provide simple operation settings and a collapsible frame for easy transport. The separator keeps the dust out of your vac and filter to allow for more effecient work. – 110V – 3 Motors – Weighs 176 lbs -Jet Pulse Filter cleaning – Includes wand, brush head and HEPA filter – 330 CFM – 26 Foot Hose